Installing A Bath tub
Installing A Bath tub
Blog Article
The content following next relating to How to Install a Bathtub is seriously engaging. Check it out yourself and decide what you think about it.
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately tough task. If the old tub is readily obtainable, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually certified yourself for the work and fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to take into consideration employing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This article will certainly aid you install a new tub in your washroom if you have already purchased a new bathtub and do not require to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist ought to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome as a result of the restricted accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the tap in place with the supplier supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub till the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly resolve it into its final setting.
Getting ready for the Installment
To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with moisture and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our blog. Are you aware of anybody else who is excited about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Be sure promote it. Bless you for your time. Visit us again soon.
Quote & Schedule
Report this page